One-systems PM4-M V4 Uživatelský manuál stáhnout pdf

POLE MOUNT SYSTEM PM4/M

INSTALLATION MANUAL

January 2015

The Pole Mount System PM4/M is an easy to install and flexible system designed

to allow ONE SYSTEMS loudspeaker systems to be mounted to pole structures.

The only products approved for use with PM4/M are the 112/HTH, 212/HC,

312/HC, 118/HSB (See Appendix 2 if the 118HSB is used), and CFA-2/HTH.

NO OTHER LOUDSPEAKERS SHOULD BE SUBSTITUTED!

The following actions MUST be performed PRIOR to beginning the installation of

the PM4/M:

1. This installation guide must be completely read and understood

2. The instruction manual “Rigging and Suspension of ONE SYSTEMS

Products” must be read and understood. (This instruction manual is

available at www.ONESYSTEMS.com

in the “Education section of

the web site.

3. The manufacturer of the pole MUST be consulted to verify the

applicability of the PM4/M and ONE SYSTEMS loudspeaker to the

specific pole. The pole must be capable of supporting the weight of

the PM4/M, the loudspeaker enclosure and all associated rigging

and ALSO meet all required safety factors specified by local and

national codes and safe rigging practices. The weight of PM4/M is

16.1 kg (35.5 lb.)

4. The PM4/M loudspeaker should be installed only by one

experienced in the overhead suspension of items and familiar with

the applicable local and national codes governing installation of

these products and also governing the attachment of these products

to the specific pole structure.

5. The installer should be experienced with the use of stainless steel

banding systems and banding system tools.

1 2 3 4 5 6 ... 12 13

Shrnutí obsahu

Strany 1 - January 2015

POLE MOUNT SYSTEM PM4/M INSTALLATION MANUAL January 2015 The Pole Mount System PM4/M is an easy to install and flexible system designed to allow O

Strany 2 - INSTALLATION

The assembly may be configured with any combination of turnbuckle, chain link sections and quick link in order to achieve the proper tension on the sy

Strany 3

Figure 7 represents a down tilt angle of 20 degrees from vertical and is shown with the chain section, three quick links and the turnbuckle. Angles o

Strany 4

APPENDIX 1 Projected Area Values The values below should be supplied to the specific pole manufacturer for safety calculations. These values were d

Strany 5

APPENDIX 2 If the PM4-M is being used with the One Systems 118/HSB the silicone gasket (supplied with th

Strany 6

6. The PM4/M is constructed with 316 grade stainless steel. The specific selection of banding material will be determined by the environment. See pa

Strany 7

Figure 1 showing M10 thru bolts Figure 1 represents the isometric and top views of the pole bracket, including the loudspeaker bracket section. T

Strany 8

Figure 3 is a representation of the Link assembly. This assembly MUST be used whenever the PM4-M is being used. Figure 3 Mount the pole mount s

Strany 9

IMPORTANT: It is REQUIRED that each of the six (6) band slots be wrapped TWICE (TWO INDEPENDENT SINGLE WRAPS PER SLOT). This should not be confused w

Strany 10

The required banding and buckle material is based on the specific installation environment. The term “inland” refers to non-industrial and non-marine/

Strany 11

Installation instructions from BAND-IT should be followed exactly. Operating instructions are supplied with the tensioning tool. (All BAND-IT parts an

Strany 12

Remove the four (4) plastic covers on the rear of the enclosure (if installed) to mount the bracket assembly to the rear of the enclosure. 2. Now

Strany 13 - APPENDIX 2

FIGURE 5 UNDER NO CIRCUMSTANCES SHOULD THE LOUDSPEAKER DOWN TILT EXCEED 35 DEGREES FROM VERTICA